Rubber Track Use Precautions
01
Before installing the track, you must check whether the main dimensions such as the width, pitch, length, inner and outer rail width of the track match the parameters such as the weight of the main machine, the size of the chassis, and the size of the train. If the mismatch does not match, the track will be seriously damaged or broken.
02
Keep a certain tension (H=10-15mm) when using the track. If the tension is too small, it will cause the phenomenon of detachment and riding, causing scratches on the inside of the track and even causing the track to break. If the tension is too large, the track will stretch, causing abnormal wear of the core iron and the drive wheel, and even causing the core iron. Broken, the track broke.
03
It is forbidden to forcibly climb the steps or walk on the edge of the steps. This can cause damage to the track.
04
Production of a low temperature type SCR denitration catalyst.
05
It is forbidden to lean on a steep slope or make a sharp turn during walking. This can cause the wheel to be broken, the track to be damaged, and even the machine to tip over.
06
It is forbidden to go straight down the stairs. This will cause the track core to fall off and the wire to break.
07
It is forbidden to walk on rough and uneven roads. It is easy to cause the wheel to be broken, which will cause damage to the track pattern and breakage of the core iron.
08
In the environment of chemicals, oil, seawater, etc., the rubber will accelerate the aging. After using the belt in these environments, the crawler should be cleaned, and the long-term use will reduce the life of the crawler.
09
Avoid walking on gravel, gravel, steel, and rock. Will cause damage to the grounding surface of the track.
10
Do not allow the track to land on one side. Will cause damage to the crawler block and break the core iron.
11
It is forbidden to walk over the bridge. It is easy to cause the wheel to be broken, which will cause damage to the track pattern and breakage of the core iron.
12
Overload operation is prohibited. It will increase the tension of the track and accelerate the wear of the core iron. In severe cases, the core iron will break and the track will break.
13
When the track is not used for a long time, clean the dirt and oil attached to the track, and avoid direct sunlight and rain after drying. When the track is not used for a long time, adjust the track to avoid fatigue.
Before installing the track, you must check whether the main dimensions such as the width, pitch, length, inner and outer rail width of the track match the parameters such as the weight of the main machine, the size of the chassis, and the size of the train. If the mismatch does not match, the track will be seriously damaged or broken.
02
Keep a certain tension (H=10-15mm) when using the track. If the tension is too small, it will cause the phenomenon of detachment and riding, causing scratches on the inside of the track and even causing the track to break. If the tension is too large, the track will stretch, causing abnormal wear of the core iron and the drive wheel, and even causing the core iron. Broken, the track broke.
03
It is forbidden to forcibly climb the steps or walk on the edge of the steps. This can cause damage to the track.
04
Production of a low temperature type SCR denitration catalyst.
05
It is forbidden to lean on a steep slope or make a sharp turn during walking. This can cause the wheel to be broken, the track to be damaged, and even the machine to tip over.
06
It is forbidden to go straight down the stairs. This will cause the track core to fall off and the wire to break.
07
It is forbidden to walk on rough and uneven roads. It is easy to cause the wheel to be broken, which will cause damage to the track pattern and breakage of the core iron.
08
In the environment of chemicals, oil, seawater, etc., the rubber will accelerate the aging. After using the belt in these environments, the crawler should be cleaned, and the long-term use will reduce the life of the crawler.
09
Avoid walking on gravel, gravel, steel, and rock. Will cause damage to the grounding surface of the track.
10
Do not allow the track to land on one side. Will cause damage to the crawler block and break the core iron.
11
It is forbidden to walk over the bridge. It is easy to cause the wheel to be broken, which will cause damage to the track pattern and breakage of the core iron.
12
Overload operation is prohibited. It will increase the tension of the track and accelerate the wear of the core iron. In severe cases, the core iron will break and the track will break.
13
When the track is not used for a long time, clean the dirt and oil attached to the track, and avoid direct sunlight and rain after drying. When the track is not used for a long time, adjust the track to avoid fatigue.
